![]() In this case use the following command to start GsServer manually:Ĭpt_paranoia, The goodsync page was all I went off of. Installer may fail to update-rc.d if you are running Busybox-based firmware. I note the Goodsync page you linked isn’t explicit about which of the many variants of the M圜loud family of devices it is intended for (WDCloud, M圜loud, Mirror, DL, EX2, EX4, Pro) As I understand it, Goodsync is paid for software, so if you’ve paid for it, go and get support for their product. If it was Goodsync, then I’d suggest asking them. The lower-end devices don’t officially support the installation of ‘apps’. Since WD don’t officially support the use of SSH to install packages on the M圜loud (of any variant, I don’t think), it seems unlikely they’d be advocating/promoting the installation of software that must be installed via SSH. Listed as compatible by whom…? WD? Goodsync? Purchased the 4100 as it was listed as compatible with goodsync, and now we’ve wasted over 6 hours and can’t get goodsync to run GoodSync checks for new changes approximately every 3 seconds, this time quant is configurable.On File Change initiates Analyze and Sync, which results in locking of sync folder by GS lock files.If these changes are result of our own sync, they will produce no new changes to be synced.If changes occur during Analyze/Sync, they are still detected and sent to the next Analyze.We recommend to set it to at least 120 seconds (2 minutes), so that GoodSync does not start syncing until files were stable for at least 2 minutes. Note that if you had several changes (including changes performed by this or other sync jobs), the delay countdown will start with the last change that was detected. If not zero then GoodSync will wait this many seconds since the last change detected by On File Change, before starting the Analyze and Sync. If only one side of the job can be monitored, then GS will get changes only from one side.None of traditional server file systems can be monitored: FTP, SFTP, S3, SkyDrive, etc. Any of the above file systems, remotely accessed via GSTP protocol used in GS Connect.Windows shares, except some broken NAS shares that do not report changes.Windows File System, local disks, except root folder.These files systems can do file monitoring, so they can do On File Change Real Time Sync: Full Analyze is performed only on the first iteration of Real Time Sync.It Analyzes only files that were reported changed by file system, no full Analyze. ![]() Our new Real Time Sync mechanism performs On File Change synchronization: From the Goodsync website:Īnalyze and Sync this job when any file changes in left or right sync folder or its sub-folder. You should be able to get by just fine with the copy command.It appears one has to enable the “on file change” option for the real time sync function to work. I use it for everything now, and it was worth learning. I can tell you that I bothered to learn rclone because it's free, open-source, and outperformed every other program I came across for syncing things, and it supports so many endpoints. I think this subreddit is for people who are (or are trying to be) professional system(s) administrators. If you're newer to systems administration, one of the best pieces of advice I can give is to learn how to do single tasks well, because you can string them together to do whatever you need, rather than looking for some solution that does everything out of the box - that's what gets you paying for it.Įdit: missed the bit about you not being in IT. I think there might be a (possibly 3rd-party) rclone gui, but I haven't tried it. ![]() Configure it with your endpoints, test the command, throw it up in cron (or task scheduler/your choice of program if you're on Windows), and then it'll be automated. But it's got great documentation and even the help argument is great. Well, you're in sysadmin - it's a command-line utility.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |